超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性

针对100 mm超厚板TC4钛合金电子束焊接接头，采用慢应变速率拉伸方法评价接头在人造海水中的应力腐蚀敏感性，分析接头的显微组织和断口形貌，对接头的腐蚀机制进行研究. 结果表明，室温条件下应变速率为ε=1×10-6 s-1时，母材在海水中未表现出应力腐蚀敏感性；焊缝上部、中部和下部具有轻微应力腐蚀敏感性. 焊缝在海水中发生阳极溶解，产生氢吸附，导致裂纹的萌生. 同时氢扩散诱导α'相界及α'相内发生位错塞积，进而使裂纹在更低的应力水平下发生扩展.     

Probing the degenerate pattern growth of {100}<011> orientation in a directionally solidified Al-4.5 wt% Cu alloy

Degenerate pattern is a seemingly disordered morphology but it exhibits the inherently ordered crystal connected with tip-splitting and limited stability which makes it difficult to observe in the metallic system. Here we employ (100)[011] orientated planar-front seeds using directional solidification and reveal the fundamental origins of the degenerate pattern growth in an Al-4.5 wt% Cu alloy. We find that the spacing of the tip-splitting (λ) in the degenerate of the alloys followed a power law, λ∝V^−0.5, and the frequency (f) of the splitting was related to the growth velocity (V) by ƒ∝V^1.5. The dimensionless growth direction (θ/θ₀) increased monotonously and approached 0.6 with faster velocity, attributed to its anisotropy in the interface kinetics. Once growth velocity exceeded a threshold, two types of pattern transitions from degenerate to regular dendrites were proposed. One of them exhibited a random and chaotic mode and the other underwent a rotation in growth direction.     

Corrosion behaviour of Al1.3CrFeNi chemically complex alloy

In this study, corrosion behaviour of double-phase Al_1.3CrFeNi chemically complex alloy was investigated, including hot corrosion and electrochemical corrosion. Hot corrosion behaviour of Al_1.3CrFeNi alloy was explored in molten 75 wt-% Na₂SO₄?+?25 wt-% NaCl salt. The result revealed that the corrosion kinetic curve of Al_1.3CrFeNi alloy followed the exponential rate rule through mass loss measurement. In addition, it prevented that the formed corrosion layer had obvious stratification including external granular Al₂O₃ and inner porous Cr₂O₃ when corrosion time was up to 100?h. Besides, it should be noted that the Al_1.3CrFeNi alloy was sensitive to the molten salt containing chlorine, which makes the alloy surface leave voids and bring about acceleration of corrosion. Meanwhile, electrochemical corrosion resistance of Al_1.3CrFeNi alloy in NaCl solution with different concentrations (0.6, 1.0 and 2.0?mol?L^?1) was investigated at room temperature. The results revealed that Al_1.3CrFeNi alloy showed superior corrosion resistance in NaCl solution due to the existence of Al and Cr which aid the formation of protective oxide layer.     

新型镍基镁渣催化重整松木热解挥发分焦油析出特性研究

采用过量浸渍法制备了镍基镁渣催化剂，并在小型气流床气化炉上开展了松木热解挥发分的催化重整研究。评估了煅烧/催化温度、镍含量和水碳比对焦油组分的影响，同时在不同煅烧/催化温度下与Ni/γ-Al₂O₃催化剂进行了裂解焦油性能的对比。采用比表面积测试（BET）、X射线衍射（XRD）、扫描电镜（SEM）和透射电镜（TEM）对催化剂进行了表征。结果表明，当镍含量为3%，煅烧/催化温度为800℃，水碳比为0.5时，镍基镁渣催化剂表现出最优异的催化裂解焦油能力：大幅度降低了重质多环芳烃的相对含量，并且焦油转化率达到95.69%，同时焦油露点温度降至40.2℃。XRD结果表明，Ni、Fe、Ca、Mg相互作用可以形成多种活性中心，进而协同提高催化剂活性。     

邻菲罗啉光度法测定钒铝合金中铁

应用邻菲罗啉光度法测定钒铝合金试样中铁时,存在试样溶解难且试样中高含量钒会干扰铁的测定的问题。实验采用硝酸、盐酸溶解试样,硫酸冒烟赶尽氮氧化物,加入盐酸羟胺将钒(V)还原为钒(IV),在沸水浴条件下加入乙酸-乙酸铵缓冲溶液消除钒(IV)的干扰,从而实现了钒含量高的钒铝合金中铁的测定。实验表明,显色液中铁的质量浓度在0~1.2μg/mL符合郎伯比尔定律,校准曲线的线性相关系数R²=0.9998;测定下限为0.005%(质量分数)。方法用于钒铝合金中铁含量的测定,测定结果相对标准偏差RSD(n=8)小于3%,回收率在98%~103%之间。按照本法和DB51/T 2038—2015《钒铝合金 硅、铁等15种杂质元素含量的测定 电感耦合等离子体原子发射光谱法》分别测定4个钒铝合金样品中铁,两种方法测定结果相一致。     

镍基高温合金液相扩散焊接头组织及性能

镍基高温合金GH4413在高温下具有较为优异的高温持久强度和抗蠕变性能，在航空发动机和各种工业燃气轮机中得到广泛应用。以BNi 2作为填充合金材料使用液相扩散焊对GH4413合金进行了连接，研究了在焊接温度分别为1 030和1 080 ℃、保温时间分别为30和60 min等不同焊接参数下GH4413镍基高温合金的接头微观组织、成分分布和显微硬度。扫描电镜(SEM)以及能谱分析结果表明，当焊接温度为1 080 ℃、保温时间为60 min 时，钎缝组织中形成了性能良好的固溶体，且随着焊接温度的升高和保温时间的延长，钎缝的宽度增加，钎料元素向母材中的扩散深度逐渐增加，在母材近缝区形成了金属间化合物。     

钛/铝异种金属冷金属过渡增材制造

采用TC4和ER2319焊丝直流/变极性冷金属过渡实现异种金属电弧增材制造，通过金相显微镜、扫描电镜、透射电镜、能谱、硬度试验、纳米压痕以及拉伸试验等方法对钛/铝构件界面组织特征与力学性能进行分析.结果表明，在钛合金表面堆积铝合金时，只有少量的钛合金熔化，钛原子扩散到液态铝合金中，形成不同长度的TiAl₃金属间化合物.10 μm左右的反应层在钛/铝界面形成.邻近钛侧的反应层均匀连续，靠近铝合金一侧的反应层呈现长条状或块状.界面反应层的显微硬度介于钛合金和铝合金显微硬度之间.构件的最高抗拉强度为111 MPa.     

Eliciting and measuring hesitance in decision-making

Hesitance is an innate human psychological phenomenon pervasive in our daily life. Although it is very complex and still not fully understood, there have been many studies related to this interesting topic. In this study, we proposed two fundamental problems about hesitance: the first is the generating problem, which is related to how to elicit hesitance information from human thinking; the second is the measuring problem, which is related to how to devise effective and reasonable methods to measure hesitance degrees from given hesitance information. With these two fundamental questions, we first discussed and analyzed several examples in real life involving hesitance, showing that it can indeed be recorded and represented. Then we roughly classified the hesitance information into two major classes: static hesitance and dynamic hesitance. Some simple and interesting methods were proposed to elicit hesitance, and more reasonable methods were proposed to measure the hesitance degree from the two classes of hesitance information. All methods that have been discussed in this study try to avoid complexity in every aspect while reserving strictness and reasonability; therefore, the present study provides suitable information for practitioners with different backgrounds.     

Strain rate and orientation-dependent strain hardening of Mg–9Li–Al using crystal plasticity

A crystal plasticity finite element model was proposed considering slip and twinning interactions. The grain morphology and crystallographic orientations were introduced into the model to describe the microstructure of duplex polycrystalline Mg–9Li–Al. The activation of the slip systems and the strain localisation with respect to initial grain orientations were investigated. In addition, the effects of phase distributions and volume fractions on the macroscopic responses and on strain hardening rates were analysed. The results show that the strain hardening is rate-dependent but the texture is less sensitive to strain rate. The distribution of a phase and its volume fraction play primary roles in governing the mechanical response.     

Effect of extrusion temperature on mechanical properties of as-extruded Zn–22Al alloys

ABSTRACT

The effect of extrusion temperature on the microstructures and mechanical properties of as-extruded Zn–22Al alloys was investigated in this study. With decrease of extrusion temperature from 350 to 200°C, the elongation of as-extruded Zn–22Al alloys increases remarkably at low strain rate and has no change at high strain rate, which implies that the Zn–22Al alloys extruded at lower temperature exhibit high-ductility behaviour. X-ray diffraction and electron back-scattered diffraction analysis demonstrated that the maximum elongation of Zn–22Al alloys extruded at the extrusion temperature of 200°C can be attributed to the elimination of the lamellar structure and the refinement in grain size of the Zn-rich phase.